The sensors are designed to be operated in a chemically non-aggressive environment.
Contact Temperature Sensors with a Plastic Connection Head
- Home
- Products
- Sensors and Probes
- Temperature Sensors
- Temperature Sensors with a Connection Head up to 600 °C
- Temperature Sensors up to 250°C
- Contact Temperature Sensors with a Plastic Connection Head
The sensors are designed to be operated in a chemically non-aggressive environment.
Specification
Sensor type (K - with connector) |
Type of sensing element | Maximum measuring DC current | Measuring range |
---|---|---|---|
NS 140 NS 140K |
Ni 1000/5000 | 1 mA | -50 to 130 °C (connection head ambient temperature -30 to 100°C) |
NS 141 NS 141K |
Ni 1000/6180 | 1 mA | |
NS 142 NS 142K |
Ni 891 | 1 mA | |
NS 340 NS 340K |
Ni 10000/5000 | 0,3 mA | |
NS 341 NS 341K |
Ni 10000/6180 | 0,3 mA | |
NS 143 NS 143K |
T1 = Ni 2226 | 0.7 mA | -50 to 130 °C (connection head ambient temperature -30 to 100°C) |
PTS 140 PTS 140K |
Pt 100/3850 | 3 mA | |
PTS 240 PTS 240K |
Pt 500/3850 | 1,5 mA | |
PTS 340 PTS 340K |
Pt 1000/3850 | 1 mA | |
HS 140 HS 140K |
thermistor NTC 20 kΩ | 1 mW *) |
*) maximum power consumption
Note: x = version A or version B
Sensor type | NK 560 | Note |
---|---|---|
Type of sensing element | Pt 1000/3850 | |
Output signal | 4 to 20 mA | |
Measuring ranges **) |
-50 to 50 °C -30 to 60 °C 0 to 35 °C 0 to 100 °C 0 to 150 °C |
ambient temperature around the connection head -30 to 70 °C |
Power supply (U) | 11 to 30 VDC | recommended value 24 VDC |
Load resistance |
150 Ω for power supply 12 VDC 700 Ω for power supply 24 VDC |
|
Output signal - sensing elements break | > 24 mA | |
Output signal - sensing element short circuit | < 3.5 mA |
**)According to the customer‘s requirement, it is possible to provide a customized measuring range from -40 to 150 °C; the minimum span of the range must be 35 °C (e.g. -20 to 15 °C; -30 to 80 °C)
Others Parametrs | |
---|---|
Accuracy class |
Ni sensing elements: B class, Δt = ± (0.4 + 0.007t), for t ≥ 0; Δt = ± (0.4 + 0.028|t|), for t ≤ 0 in °C; Pt sensing elements: B class according EN 60751, Δt = ± (0.3 + 0.005|t|) in °C NTC 20 kΩ: ± 1 °C for the range 0 to 70 °C |
Measuring error for NS 540(K), NS 740(K) *), **) | < 0.6 % of the measuring range, minimum 0.5 °C |
Sensor connection | according to the wiring diagram |
Time response | τ0,5 < 4 s (in flowing water at 0.4 m.s-1) |
Recommended wire cross section - sensors with the grommet | 0.35 to 1.5 mm2 |
Type of connector in the head - sensors with connector | RSFM4 - Lumberg |
Insulation resistance | > 200 MΩ at 500 VDC, 25° ± 3 °C; humidity < 85 % |
Ingress protection | IP 65 in accordance with EN 60529 |
Material of the case | brass |
Material of connection head | POLYAMIDE |
Standard strap length | 40 cm |
Minimum pipe diameter | 20 mm |
Operating conditions |
|
Weight | approximately 0.15 kg |
*) The temperature sensor´s measurement error is dependent on the influence of ambient temperature, environmental variables and the characteristics of the measured surface (error of method).
**) It is recommended to apply heat-conducting paste or silicon grease to the measured surface, which will ensure faster response time and minimise the measurement error of the contact temperature sensor.
Note: Manufacturer reserves the right to make changes in design and technical characteristics of the products. For actual information, please always contact your deale
Dimensional Draft
Wiring Diagram
Also, you can reach us on +44 (0) 1865400514